Difference between revisions of "Minibot Controller/XL-320"
From Lofaro Lab Wiki
(3 intermediate revisions by the same user not shown) | |||
Line 36: | Line 36: | ||
[[File:Minibot_Controller_(4).png]] | [[File:Minibot_Controller_(4).png]] | ||
− | *As Previous part, connect wire before putting forearm. | + | *As Previous part, '''connect wire before putting forearm'''. |
[[File:Minibot_Controller_(5).png]] | [[File:Minibot_Controller_(5).png]] | ||
[[File:Minibot_Controller_(6).png]] | [[File:Minibot_Controller_(6).png]] | ||
Line 43: | Line 43: | ||
[[File:Minibot_Controller_(7).png]] | [[File:Minibot_Controller_(7).png]] | ||
+ | *Connect Elbow (Part2) with Upper arm (Part3). | ||
[[File:Minibot_Controller_(8).png]] | [[File:Minibot_Controller_(8).png]] | ||
[[File:Minibot_Controller_(9).png]] | [[File:Minibot_Controller_(9).png]] | ||
+ | |||
+ | *Connect (Part4) to the servo using indicated holes and rivets. | ||
[[File:Minibot_Controller_(10).png]] | [[File:Minibot_Controller_(10).png]] | ||
+ | |||
+ | *Connect (Part4) to Upper arm (Part3). | ||
[[File:Minibot_Controller_(11).png]] | [[File:Minibot_Controller_(11).png]] | ||
+ | |||
+ | *To connect arm to shoulder, Put (Part5) to arm. | ||
[[File:Minibot_Controller_(12).png]] | [[File:Minibot_Controller_(12).png]] | ||
+ | |||
+ | |||
[[File:Minibot_Controller_(13).png]] | [[File:Minibot_Controller_(13).png]] | ||
[[File:Minibot_Controller_(14).png]] | [[File:Minibot_Controller_(14).png]] | ||
+ | |||
+ | |||
[[File:Minibot_Controller_(15).png]] | [[File:Minibot_Controller_(15).png]] | ||
+ | |||
[[File:Minibot_Controller_(16).png]] | [[File:Minibot_Controller_(16).png]] | ||
+ | |||
[[File:Minibot_Controller_(17).png]] | [[File:Minibot_Controller_(17).png]] | ||
+ | |||
+ | |||
[[File:Minibot_Controller_(18).png]] | [[File:Minibot_Controller_(18).png]] | ||
+ | |||
[[File:Minibot_Controller_(19).png]] | [[File:Minibot_Controller_(19).png]] | ||
+ | |||
[[File:Minibot_Controller_(20).png]] | [[File:Minibot_Controller_(20).png]] |
Latest revision as of 13:04, 17 April 2015
This is the instruction of building the controller for Minibot.
Notes :
- The zero positions will be placed as same as how Minibot is assembled
- - Instruction of Minibot indicates to place zero positions to be at top.
- There are only one arm in the instruction.
- Face the servo as shown in image for one arm.
- Another arm will be mirrored to the instruction.
- 2-step rivets are used for all instruction except indicated section.
3D printing :
- STL files are uploaded here.
- You might need to convert STL files to 3D printable file.
The claw
- For movable part of the hand, one of the side of servo will not have wheel; Connect Servo with the hand by putting rivet in the middle hole only.
- On the other side of the servo, For upper hand, put rivets on outer holes.
Forearm
- Before connecting next part, Connect wire to the servo. Then connect Forearm (Part1).
- As Previous part, connect wire before putting forearm.
- Connect Elbow part (Part2), similar as you put the upper hand, put 4 rivets on side with wheel, and 1 on the other side.
- Connect Elbow (Part2) with Upper arm (Part3).
- Connect (Part4) to the servo using indicated holes and rivets.
- Connect (Part4) to Upper arm (Part3).
- To connect arm to shoulder, Put (Part5) to arm.