|
|
| Line 5: |
Line 5: |
| | 3. Install Hubo-ach from [https://github.com/hubo/hubo-ach here] | | 3. Install Hubo-ach from [https://github.com/hubo/hubo-ach here] |
| | | | |
| − | 4. Download the github code for the ARCHR peg-in-hole from [https://github.com/LofaroLabs/Simulation/tree/master/archr_drc here], and save the entire contents in a folder called 'Hubo_Simulation' | + | 4. Instructions for running the ARCHR code can be found [http://wiki.lofarolabs.com/index.php/Hubo_DRC_Peg-In-Hole_%26_Valve_Turn here] |
| − | | + | |
| − | 5. Run openrave with hubo-ach with the command: hubo-ach sim openhubo physics drc
| + | |
| − | | + | |
| − | 6. Run the python keyboard example 'HuboKeyboardControl.py' and press the appropriate keyboard key for performing manipulations on the various limbs of DRC. For example, pressing 'a' moves the RSP up 0.1 radians, 'z' moves it down 0.1 radians.
| + | |
| − | | + | |
| − | All joints and keys are shown below:
| + | |
| − | * if c == 'a': RSP = RSP-0.1;
| + | |
| − | * if c == 'z': RSP = RSP+0.1;
| + | |
| − | * if c == 's': RSR = RSR-0.1;
| + | |
| − | * if c == 'x': RSR = RSR+0.1;
| + | |
| − | * if c == 'd': RSY = RSY-0.1;
| + | |
| − | * if c == 'c': RSY = RSY+0.1;
| + | |
| − | * if c == 'f': REB = REB-0.1;
| + | |
| − | * if c == 'v': REB = REB+0.1;
| + | |
| − | * if c == 'g': RWY = RWY-0.1;
| + | |
| − | * if c == 'b': RWY = RWY+0.1;
| + | |
| − | * if c == 'h': RWP = RWP-0.1;
| + | |
| − | * if c == 'n': RWP = RWP+0.1;
| + | |
| − | * if c == 'w': RF1 = 1;
| + | |
| − | * if c == 'e': RF1 = -1;
| + | |
| − | * if c == 'r': RF2 = 1;
| + | |
| − | * if c == 't': RF2 = -1;
| + | |
| − | | + | |
| − | * note: RF1 and RF2 require a value of 1 or -1 to open or close the two portions of the hand.
| + | |
| − | | + | |
| − | 7. The various arms of the DRC can be commanded via a controller consisting of dynamixel servos, and running the code in the file 'ARCHR_hubo_peg.py'. The various actuator numbers and servo IDs must be modified in the file to match your dynamixel configuration.
| + | |
| − | | + | |
| − | * Valve-turn is in prototype stage and may not be completed, a sample environment is included in the link above. It can be selected by modifying the 'VirtualHubo.py' file located in the '/etc/hubo-ach' folder after successful hubo-ach installation, and selecting the line for valve-turn.
| + | |
Revision as of 02:00, 17 December 2014
1. Install openRAVE version 0.9.0 from here (compile it from sources)
2. Install openHubo from here
3. Install Hubo-ach from here
4. Instructions for running the ARCHR code can be found here
